Solar and battery installation in Mount Druitt
Not one Mount Druitt job on the record carries a system size, so this page publishes no local figure. Instead it sets out how to size a system from your own bill, and what the heat here does to output.
Solar in Mount Druitt: no local figure, so here is how to work out your own
Mount Druitt accounts for four completed Crown Solar installations, and not one of them carries a recorded system size. So this page publishes no local sizing figure, because there is none to publish. Borrowing a number from a neighbouring suburb and calling it local would be inventing evidence, and the standard on these pages is that a figure is either on the record or it is not stated.
What the record does show is that the recent Mount Druitt work is storage: batteries, and solar with a battery together. That is consistent with a suburb where a lot of panels went on roofs years ago and households are now completing the system.
Rather than leave the sizing question empty, the section below sets out how it is actually answered. From your own bill. That is the method used on every job regardless of suburb, and in a suburb with no local record it is all the more worth spelling out.
One note on the postcode. 2770 covers Mount Druitt and a large group of neighbouring suburbs, so a postcode search returns results from across a wide area rather than from your street. For the export timetable the postcode is what counts; for the design, the street and the roof are.
Who owns the roof
This comes before the engineering, because it decides whether there is a job at all.
If you rent, the decision belongs to the owner. For a private tenancy that is your landlord or the managing agent. For a social housing tenancy it is Homes NSW. The right first step is to ask them rather than to collect quotes, because no installer can work on a roof without the owner's authority, and Crown Solar will not pretend otherwise to book an appointment. If you are paying the electricity bill and a system would help, that is a reasonable thing to raise with whoever owns the property.
If you own your home, the rest of this page is written for you.
How a system is actually sized
This is the useful part, and it needs no local average at all.
Start with twelve months of bills, not a single quarter. A summer bill and a winter bill describe different households. What matters is total annual consumption in kilowatt-hours and how it is distributed across the year, which the bills give you directly.
Then split that between daytime and after dark. This is the figure that decides everything. The daytime share is what an array can serve directly. The after-dark share is what only a battery or the grid can serve. Many retailers now provide interval data on request or through an online portal, and a smart meter makes this precise rather than estimated. Without it, an installer is guessing, and you are entitled to ask which it is.
Size the array against daytime use plus whatever you can usefully export. Until flexible exports reach 2770 a fixed export limit applies, so generation you cannot use and cannot export is generation you paid for and will never see. That is the arithmetic that sometimes makes a smaller array plus a battery better value than a bigger array alone.
Size the battery against evening and overnight consumption. Not against the size of the array, and not against a feeling about blackouts. A smaller battery that is actually cycled every day beats a large one that is rarely emptied.
Then check what the roof can carry. Usable north and west faces, not total roof area. The roof frequently sets a lower ceiling than the budget does, and an honest design says so rather than filling a southern face to reach a headline number.
Finally, account for the things that will change. An electric vehicle, a switch from gas to electric cooking or hot water, or a reverse-cycle system replacing a gas heater all move the figure materially. If one of those is likely within a couple of years, it belongs in the sizing conversation now.
Your grid connection: Endeavour Energy, postcode 2770
Mount Druitt is in the Endeavour Energy distribution area. Endeavour approves the connection and sets the export limit. Your electricity retailer does neither.
Where 2770 sits in Endeavour's rollout
Endeavour stages flexible exports by postcode, not by council.
-
Stage 1, commenced 2 November 2026 Postcodes in and around the Campbelltown, Camden, Picton and Liverpool regions.
-
Stage 2, commences 30 November 2026 A further set of postcodes across Endeavour's area. Postcode 2770 is in this stage
-
Phase 3, February 2027 Endeavour has published the month and not a day within it. Its rollout map gives the date for a specific address.
What you may export, by connection type
Endeavour Energy, kilowatts per phase.
Flexible exports reach 2770 in the February 2027 phase
Endeavour has published two rollout stages by postcode. The first commenced on 2 November 2026, covering postcodes in and around the Campbelltown, Camden, Picton and Liverpool regions. The second commences on 30 November 2026 and adds a long list of Blue Mountains, Penrith, Hawkesbury and Illawarra postcodes. 2770 appears in neither.
That places Mount Druitt in the February 2027 phase of Endeavour's availability plan. Endeavour has published the month, not a date within it, so this page gives the month and nothing more precise. Treat any quote that names a specific February day for 2770 as unsourced.
Blacktown council spans postcodes on more than one date, since the staging is by postcode rather than by council. Blacktown on 2148 and Glenwood on 2768 are also in the February phase, while 2765 to the north moves on 30 November. A single council-level answer is not available.
When it does apply, a flexible export connection allows up to 10kW per phase to be exported most of the time, reduced only when local grid conditions require it. The opt-out is Endeavour's Fixed Exports plan with a maximum export of 1.5kW. Until then, an application submitted and approved under the existing process carries a fixed export limit, and that position should appear on your quote in writing.
What your system has to meet
Endeavour requires an address in its network area, an active internet connection by Wi-Fi or cable, net export metering configured for the solar inverter, and a CSIP-AUS approved inverter listed on the Clean Energy Council website.
The emergency backstop mechanism allows the network to curtail exports when the grid cannot absorb what is being sent into it. Endeavour describes it as a last resort, expected to be used rarely and for short periods.
What Mount Druitt properties mean for system design
Heat costs output, and it is worse out here than on the coast. Panels are rated at a cell temperature of 25°C and output falls as the cell rises above it, and on a western Sydney roof in summer the cell runs well above air temperature. Inverters also protect themselves by reducing output once they get too hot. So the inverter position is a design decision: out of direct afternoon sun, with airflow around it, and not boxed into an unventilated cupboard. A shaded garage wall beats the convenient spot beside the meter box on the western elevation. Mounting the array with an air gap for cooling matters here too, particularly on sheet metal.
Switchboard age is the recurring cost. Much of the housing here is established, and a board of that era frequently needs replacement or upgrade before a battery, in terms of capacity, protective devices and physical space. It should be assessed and priced before you sign rather than raised on installation day. Two quotes that look far apart frequently differ on exactly this line.
Asbestos in a pre-1990 house is a constraint to plan for, not a scare. Bonded asbestos cement sheeting was used in Australian housing until the late 1980s, including eaves linings and meter box backing boards. Where it is present it changes how cable is run and who may do that work. It does not prevent a solar installation; it means the eaves and meter box are inspected during the assessment rather than discovered with a drill.
Mostly single storey, which helps. A single-storey roof is safer and quicker to work on, and usually gives better access to the full roof plane than a two-storey house.
Roof condition decides the sequence. Where a roof is close to needing replacement or significant repair, doing that first and the solar second is cheaper than paying to remove and refit an array later. The roof is assessed at quote stage.
Batteries in Mount Druitt
Since storage is what the local record is made of, the retrofit case deserves the detail.
The inverter decides most of the cost. Adding storage is treated as an upgrade, which brings the connection under current requirements, so an inverter that is not CSIP-AUS approved has to be replaced as part of the job. That single fact accounts for most of the gap between two retrofit quotes, which is why the make and model on your wall is the first thing checked.
If you already have panels, you have the best sizing data available. You know what the system produced, what you used and what you exported, which is far better evidence than any projection.
Siting matters in this climate. Storage has an operating temperature range and a preferred one, and both performance and service life suffer at the top of it. A hot, unventilated garage is a decision with consequences, and manufacturers' installation requirements should be followed rather than treated as advisory.
The federal battery discount is applied by the installer at the point of sale through the small-scale certificate mechanism, and the rate steps down over time. Crown Solar sets out the figure applying to your quote in writing rather than publishing one here.
Approvals: Blacktown City Council and the NSW planning rules
Mount Druitt falls within Blacktown City Council. For most rooftop installations the council is not the approval authority, because most rooftop solar in NSW is exempt development under State Environmental Planning Policy (Transport and Infrastructure) 2021 and requires no development application.
The exemption is conditional, with a capacity limit and a restriction on panels facing the street among the conditions, and a proposal that does not meet every one of them requires development consent instead. For lots near the creek lines that run through this part of Blacktown the flood position is worth establishing from council mapping, because it bears on where the inverter, battery and switchboard can safely be sited. Crown Solar checks the lot before the quote is finalised.
What the installation actually involves
Ownership and authority. Confirmed first, because without the owner's authority there is no job.
Twelve months of consumption. Bills and, where available, interval data, split between daytime and after dark.
The existing system, if there is one. Make, model, age and capacity of the inverter, whether it is CSIP-AUS approved, and whether it is battery-capable.
Site assessment. Roof material and condition, usable faces, shading, and the inverter position chosen for temperature as well as cable run.
Switchboard, meter box and eaves. Condition, capacity, and whether pre-1990 sheeting is present.
Design and quote. Array sized against daytime use, battery against overnight use, any inverter or switchboard replacement itemised, and the export arrangement that applies given the February 2027 phase.
Connection application to Endeavour Energy. Nothing is installed before approval.
Commissioning, metering and handover paperwork.
Find out what your roof can carry
The design starts with your roof and your own bill, not with a number over the phone.
Crown Solar does not quote off a template or over the phone. Every design is built on your own site data.
Common questions about solar in Mount Druitt
You have no local figures. Why should I trust the quote?
Because the quote is built from your data, not from a suburb average. A local average is a sanity check at best and misleading at worst, since it describes other people's houses. What makes a quote trustworthy is that the consumption figures, the roof faces, the inverter decision and the export position are all written down and checkable.
Should I wait for February 2027?
Generally not, and for a battery retrofit it matters even less, because storage is about self-consumption rather than export. What you should insist on is the arrangement being stated in writing on the quote.
What should I ask every installer who quotes me?
Where the inverter will be mounted and why, whether the existing inverter is being kept or replaced, whether the switchboard has been inspected and priced or merely assumed, and what export arrangement applies at your address in writing.
What Crown Solar installs here
With no recorded system size locally, this page will not dress the Mount Druitt record up as a local sizing norm or an equipment preference. What Crown Solar installs is the same range everywhere, stated plainly.
The panel Crown Solar is currently installing is Trina Solar, fitted as the high-wattage Vertex range. On the local record Jinko Solar is the panel on the Mount Druitt roof on file, from the earlier years of this work. Crown Solar also installs JA Solar, AE Solar and LONGi panels.
Inverters and storage
FoxESS accounts for the recorded inverters and batteries on the Mount Druitt jobs, on all three that carry equipment detail.
Crown Solar also installs Sungrow, Fronius, GoodWe and SAJ inverters, and Tesla Powerwall, Sigenergy and AlphaESS batteries. Which one suits depends on whether you want whole-home backup, whether you expect to expand later, and whether you intend to join a virtual power plant. In this climate the operating temperature range and the siting requirements are a real part of that comparison rather than fine print. Those are the current range, available on any job, not a list of what has been fitted locally.
Talk to Crown Solar about your Mount Druitt home
Crown Solar is a NSW electrical contractor, licence 378172C, and a New Energy Tech Approved Seller. The office is at 3B/4 Louise Avenue, Ingleburn, and is open Mon–Fri 9am–5pm.
For a quote on a Mount Druitt address you own, call 1800 38 50 38, email info@crownsolar.com.au, or use the contact form.
Get it in writing for your Mount Druitt address
Send the address and your last four quarterly bills. You get a system size, the roof faces it sits on, the export arrangement, and the price. All in writing.
Prefer email? info@crownsolar.com.au. One question to start with: what is your place using in a quarter?