Solar and battery installation in Kellyville
On a large Kellyville block the distance between the roof, the switchboard and the inverter position is a real cost. No local system size is recorded, so this page is about the things that actually decide a design here.
Solar in Kellyville: on a big block, distance is a design problem
Kellyville accounts for four completed Crown Solar installations, and none of them carries a recorded system size. So this page publishes no local sizing figure, because there is none to publish. Borrowing one from a neighbouring suburb and calling it local would be inventing evidence.
What is worth saying about Kellyville instead is something the kilowatt figure would hide. The housing here sits on larger blocks than almost anywhere else on this site except the acreage suburbs, with substantial two-storey homes, detached and attached garages, and sometimes outbuildings. On a property like that, the distance between the roof, the switchboard and the inverter position is a cost in its own right, and it is the thing most quotes never mention.
Kellyville is in The Hills Shire Council area on postcode 2155.
Distance: cable, voltage drop and where the inverter goes
Voltage drop over distance is a real loss, not a technicality. Running cable a long way from a far roof plane or a detached garage back to the main switchboard means heavier cable to keep the loss within limits. Heavier cable costs money. Undersize it and you lose output for the life of the system, quietly, in a way no one notices because there is nothing to compare against. The run is calculated rather than estimated, and on a large block it can change which roof is worth using even when another has the better aspect.
The inverter position is a genuine decision here. It needs to be close enough to keep the DC run sensible, out of direct afternoon sun because inverters reduce their own output when they overheat, accessible for service, and inside the required clearances. On a big house those four pull in different directions, and the convenient spot next to the meter box is often the worst one on three of them.
And the internet requirement bites hardest on exactly this kind of property. Endeavour requires an active internet connection at the inverter by Wi-Fi or cable. In a large two-storey house with the router at one end and the inverter in a detached garage at the other, that is frequently the weakest signal on the property. It is a connection requirement, not a nice-to-have, so the signal at the inverter position is checked during the assessment rather than discovered at commissioning. Where it fails, a cable run or a dedicated link becomes part of the job and belongs on the quote.
What to ask. Where the inverter is going and why, and whether the cable run has been calculated. An installer who has thought about a Kellyville block can answer both.
Your grid connection: Endeavour Energy, postcode 2155
Kellyville is in the Endeavour Energy distribution area. The Kellyville job on Crown Solar's record that carries a meter identifier shows an Endeavour network prefix. Endeavour approves the connection and sets the export limit. Your electricity retailer does neither.
Where 2155 sits in Endeavour's rollout
Endeavour stages flexible exports by postcode, not by council.
-
Stage 1, commenced 2 November 2026 Postcodes in and around the Campbelltown, Camden, Picton and Liverpool regions.
-
Stage 2, commences 30 November 2026 A further set of postcodes across Endeavour's area.
-
Phase 3, February 2027 Endeavour has published the month and not a day within it. Its rollout map gives the date for a specific address. Postcode 2155 is in this stage
What you may export, by connection type
Endeavour Energy, kilowatts per phase.
Flexible exports reach 2155 in the February 2027 phase
Endeavour has published two rollout stages by postcode. The first commenced on 2 November 2026, covering postcodes in and around the Campbelltown, Camden, Picton and Liverpool regions. The second commences on 30 November 2026 and adds a long list of Blue Mountains, Penrith, Hawkesbury and Illawarra postcodes. 2155 appears in neither, which places Kellyville in the February 2027 phase of Endeavour's availability plan. Endeavour has published the month, not a date within it, so this page gives the month and nothing more precise. Treat any quote that names a specific February day for 2155 as unsourced.
The Hills Shire is split across dates, because the staging is by postcode rather than by council. Castle Hill on 2154 is also in the February phase, while Box Hill on 2765 moved on 30 November. Advice written for "The Hills" cannot get this right for your address.
When it applies, a flexible export connection allows up to 10kW per phase to be exported most of the time, reduced only when local grid conditions require it. The opt-out is Endeavour's Fixed Exports plan with a maximum export of 1.5kW. Until the rollout reaches 2155, an application submitted and approved under the existing process carries a fixed export limit, and that position should appear on your quote in writing.
Three-phase supply is reasonably common on larger Hills homes, and since the allowance applies per phase, that changes the sizing arithmetic substantially. Establish your supply type before comparing quotes.
What your system has to meet
Endeavour requires an address in its network area, an active internet connection by Wi-Fi or cable, net export metering configured for the solar inverter, and a CSIP-AUS approved inverter listed on the Clean Energy Council website.
Larger systems carry a further consideration. Streamlined approval pathways apply up to certain inverter capacity thresholds, and above those a proposal can require a more detailed network assessment, which takes longer and may carry a cost. On a large Kellyville home that is worth checking before equipment is ordered.
The emergency backstop mechanism allows the network to curtail exports when the grid cannot absorb what is being sent into it. Endeavour describes it as a last resort, expected to be used rarely and for short periods.
What else Kellyville properties mean for system design
Complex roofs with many faces. A large contemporary house typically has a hip-and-valley roof with gables and a separate garage plane, so the usable area is smaller than the roof looks and the array splits across more faces than a simple roof needs. That changes inverter and string selection, which is a design decision rather than an arithmetic one.
The house shades itself. On a two-storey home with a lower rear or garage roof, the upper storey can shade part of that lower plane for much of a winter morning. It is one of the most commonly missed items in a desktop design and it is measured on site.
Tree cover, and tree rules. Hills blocks carry substantial established planting. A tree that casts nothing on the roof in January can cover a third of an array at nine in the morning in June, because the sun is roughly thirty degrees lower, so shading is assessed for the winter sun path rather than from how the roof looks on the day of the visit. The Hills Shire also regulates tree removal and significant pruning, and permission is required in many cases, so the honest approach is to design around the canopy you have and treat pruning as a separate application you may or may not get.
Roof age varies across the suburb. Kellyville spans a long build-out, so roof material, roof age and switchboard condition have to be established property by property. On the older tile roofs, ridge pointing and valley irons commonly need attention at around the thirty-year mark, and doing that work after an array is installed means paying to remove and refit it. The roof is assessed at quote stage.
Switchboard capacity, not just condition. For a large system and any battery the question is whether the board has the capacity, the protective devices and the physical space for what is being added, and on a three-phase installation there is more protection to fit. It is assessed and priced before you sign rather than raised on installation day.
Estate covenants. Many Hills releases carry restrictions registered on the title, including covenants on external appearance. They are a private arrangement rather than a council matter, but they are enforceable, and they are checked against the lot before the layout is fixed.
Batteries in Kellyville
A battery is sized against evening and overnight consumption, not against the size of the array. On a larger home with ducted air conditioning, electric hot water or a pool pump, that evening figure can be high enough to justify real capacity, which is a reason to look at the interval data rather than a reason to assume. Many retailers provide it on request or through an online portal.
A smaller battery that is actually cycled every day beats a large one that is rarely emptied. Oversized storage is an expensive way to feel prepared.
On a big property, where the battery goes is part of the design, for the same distance and temperature reasons as the inverter. Storage has an operating temperature range and a preferred one, and both performance and service life suffer at the top of it, so a hot unventilated garage is a decision with consequences.
Where a battery is being retrofitted, the inverter decides most of the cost. Adding storage is treated as an upgrade, which brings the connection under current requirements, so an inverter that is not CSIP-AUS approved turns an addition into a replacement plus an addition.
Decide what backup means to you before the equipment is chosen. Whole-home backup, a nominated essential circuit, or no backup at all are three different specifications at three different prices, and on three-phase supply the backup configuration is a further decision again.
The federal battery discount is applied by the installer at the point of sale through the small-scale certificate mechanism, and the rate steps down over time. Crown Solar sets out the figure applying to your quote in writing rather than publishing one here.
Approvals: The Hills Shire Council and the NSW planning rules
Kellyville falls within The Hills Shire Council. For most rooftop installations the council is not the approval authority, because most rooftop solar in NSW is exempt development under State Environmental Planning Policy (Transport and Infrastructure) 2021 and requires no development application.
The exemption is conditional, with a capacity limit and a restriction on panels facing the street among the conditions, and a proposal that does not meet every one of them requires development consent instead. It also carries limits on land with heritage significance, and The Hills Shire maintains a heritage schedule and conservation areas. Toward the bushland edges, bushfire-prone land mapping is worth establishing as well, because where a lot is mapped it bears on where ground-level equipment is sited and how cable is routed, which on a large block interacts directly with the distance question above. Crown Solar checks the lot before the quote is finalised.
What the installation actually involves
Site assessment across the whole property. Every candidate roof plane with orientation, pitch and condition, and the winter shading pattern measured.
Supply and switchboard. Single or three phase, switchboard location and capacity, and the distance from each candidate roof to it.
Cable run calculation. Voltage drop for each option, which can decide which roof is used.
Inverter and battery positions. Chosen for cable length, temperature, ventilation, service access and clearances, with the internet signal checked at the actual position.
Title, planning and bushfire check on the lot. Any registered covenants, heritage mapping, and bushfire status.
Design and quote. Layout by roof face, battery sizing against overnight use with the backup specification stated, and the export arrangement that applies given the February 2027 phase.
Connection application to Endeavour Energy. Nothing is installed before approval.
Commissioning, metering and handover paperwork.
Find out what your roof can carry
The design starts with your roof and your own bill, not with a number over the phone.
Crown Solar does not quote off a template or over the phone. Every design is built on your own site data.
Common questions about solar in Kellyville
Should I wait for February 2027?
Generally not. Most of the value of a solar system is in the energy you use yourself rather than the energy you export, and on a larger home with a substantial daytime load that is especially true. What you should insist on is the arrangement being stated in writing on the quote.
Castle Hill is the same council. Why is its date the same but Box Hill's different?
Because Endeavour stages by postcode. Castle Hill is 2154 and Kellyville is 2155, both in the February phase; Box Hill is 2765 and moved on 30 November. One council, more than one date.
You have no local figures. Why should I trust the quote?
Because the quote is built from your property and your data rather than from a suburb average, which describes other people's houses. What makes it trustworthy is that the roof faces, the cable runs, the equipment positions, the consumption figures and the export position are written down and checkable.
What Crown Solar installs here
The panel Crown Solar is currently installing is Trina Solar, fitted as the high-wattage Vertex range. On the local record Jinko Solar is the panel on the Kellyville roof on file, from the earlier years of this work. That distinction is worth having if you are comparing a quote today against what a neighbour had fitted: the panel on your quote is the current one, not the one on their roof. Crown Solar also installs JA Solar, AE Solar and LONGi panels.
Inverters and storage
GoodWe appears on the recorded Kellyville inverters.
Crown Solar also installs FoxESS, Sungrow, Fronius and SAJ inverters, and Tesla Powerwall, Sigenergy and AlphaESS batteries. On a large or three-phase property the choice is narrowed first by capacity and by what you need backed up, and only then by preference, so it is made with the design rather than before it. Those are the current range, available on any job, not a list of what has been fitted locally.
Talk to Crown Solar about your Kellyville home
Crown Solar is a NSW electrical contractor, licence 378172C, and a New Energy Tech Approved Seller. The office is at 3B/4 Louise Avenue, Ingleburn, and is open Mon–Fri 9am–5pm.
For a quote on a Kellyville address, call 1800 38 50 38, email info@crownsolar.com.au, or use the contact form.
Get it in writing for your Kellyville address
Send the address and your last four quarterly bills. You get a system size, the roof faces it sits on, the export arrangement, and the price. All in writing.
Prefer email? info@crownsolar.com.au. One question to start with: what is your place using in a quarter?